DESIGNED FOR THICK, NON-FLEXING MATERIALThese compact, yet powerful, Rare Earth lift magnets can be used on flat or round surfaces and contain an internal release on/off device that does not contact or damage the surface of the part being lifted. Permanent magnetic lifts also eliminate the fear of dropping the load being lifted due to power failures.
- ON/OFF Rare Earth designLifts flat or round loadsEasy internal manual release does not contact the loadHeat resistant up to 200°F (94°C)
- CONFORMS TO ASME B30.20 STANDARDS
Lock On & Off Features
The new handle on the PowerLift® Rare Earth lift magnet features a positive lock-on and lock-off mechanism that requires the operator to manually switch between the two states. This prevents the handle from being turned only ”partially on” and giving the operator a false sense of security that the magnet is holding safely, or from being accidentally bumped to the “off” position, dropping the load pre-maturely.
| Flat Lift Capacity* (LBS.) |
Round Lift Capacity* (LBS.) |
Overall Length (IN.) |
Overall Width (IN.) |
Overall Height (IN.) |
Handle (IN.) |
Weight (LBS.) |
Catalog Number |
| 220 |
110 |
5 |
2-5/8 |
6-5/8 |
5-7/8 |
7 |
PNL220 |
| 660 |
330 |
7-7/8 |
3-5/8 |
8-7/8 |
6-7/8 |
22 |
PNL660 |
| 1,300 |
660 |
10-3/4 |
4-7/8 |
8-7/8 |
6-3/4 |
53 |
PNL1300 |
| 2,200 |
1,100 |
12-5/8 |
7-1/8 |
8-7/8 |
10-1/8 |
110 |
PNL2200 |
| 4,400 |
2,200 |
16-1/2 |
9-1/4 |
18 |
16-3/4 |
325 |
PNL4400 |
| 6,600 |
3,300 |
20 |
11-1/4 |
22-1/4 |
20-5/8 |
485 |
PNL6600 |
| *Lift CapacityValues Are Stated At 33% Of The Actual Value. See Holding Value & Maximum Sheet Length Chart Below. |
| HOLDING VALUE (LBS.) & **MAXIMUM SHEET LENGTH (Due to Sag for Material Thickness for Single Magnet Use) |
| Catalog Number |
1/4" (6' Long) |
3/8" (8' Long) |
1/2" (8' Long) |
3/4" (8' Long) |
1" (10' Long) |
2" (10' Long) |
3" (10' Long) |
| PNL220 |
180 |
220 |
220 |
220 |
220 |
220 |
220 |
| PNL660 |
270 |
500 |
615 |
660 |
660 |
660 |
660 |
| PNL1300 |
NA |
NA |
800 |
1300 |
1300 |
1300 |
1300 |
| PNL2200 |
NA |
NA |
NA |
NA |
1490 |
2200 |
2200 |
| PNL4400 |
NA |
NA |
NA |
NA |
NA |
2625 |
4400 |
| PNL6600 |
NA |
NA |
NA |
NA |
NA |
NA |
6600 |
It is recommend when lifting sheets over 8', to use 2 or more lifts on a spreader bar to prevent sheet flexing, sagging or peel-off. Thin material is susceptible to magnetic bleed through, resulting in two sheets being lifted at once. **These maximum sheet lengths are selected due to the sag characteristics of the specified sheet. The item to be lifted must cover the entire length and width of the magnetic poles to properly engage and release the part. NA=Not Applicable(magnets listed will not turn "on" for specified material thickness.)
DESIGNED FOR THICK, NON-FLEXING MATERIAL
These compact, yet powerful, Rare Earth lift magnets can be used on flat or round surfaces and contain an internal release on/off device that does not contact or damage the surface of the part being lifted. Permanent magnetic lifts also eliminate the fear of dropping the load being lifted due to power failures.
- ON/OFF Rare Earth design
- Lifts flat or round loads
- Easy internal manual release does not contact the load
- Heat resistant up to 200°F (94°C)
- CONFORMS TO ASME B30.20 STANDARDS
Lock On & Off Features
The new handle on the PowerLift® Rare Earth lift magnet features a positive lock-on and lock-off mechanism that requires the operator to manually switch between the two states. This prevents the handle from being turned only ”partially on” and giving the operator a false sense of security that the magnet is holding safely, or from being accidentally bumped to the “off” position, dropping the load pre-maturely.
| Flat Lift Capacity* (LBS.) |
Round Lift Capacity* (LBS.) |
Overall Length (IN.) |
Overall Width (IN.) |
Overall Height (IN.) |
Handle (IN.) |
Weight (LBS.) |
Catalog Number |
| 220 |
110 |
5 |
2-5/8 |
6-5/8 |
5-7/8 |
7 |
PNL220 |
| 660 |
330 |
7-7/8 |
3-5/8 |
8-7/8 |
6-7/8 |
22 |
PNL660 |
| 1,300 |
660 |
10-3/4 |
4-7/8 |
8-7/8 |
6-3/4 |
53 |
PNL1300 |
| 2,200 |
1,100 |
12-5/8 |
7-1/8 |
8-7/8 |
10-1/8 |
110 |
PNL2200 |
| 4,400 |
2,200 |
16-1/2 |
9-1/4 |
18 |
16-3/4 |
325 |
PNL4400 |
| 6,600 |
3,300 |
20 |
11-1/4 |
22-1/4 |
20-5/8 |
485 |
PNL6600 |
| *Lift CapacityValues Are Stated At 33% Of The Actual Value. See Holding Value & Maximum Sheet Length Chart Below. |
| HOLDING VALUE (LBS.) & **MAXIMUM SHEET LENGTH (Due to Sag for Material Thickness for Single Magnet Use) |
| Catalog Number |
1/4" (6' Long) |
3/8" (8' Long) |
1/2" (8' Long) |
3/4" (8' Long) |
1" (10' Long) |
2" (10' Long) |
3" (10' Long) |
| PNL220 |
180 |
220 |
220 |
220 |
220 |
220 |
220 |
| PNL660 |
270 |
500 |
615 |
660 |
660 |
660 |
660 |
| PNL1300 |
NA |
NA |
800 |
1300 |
1300 |
1300 |
1300 |
| PNL2200 |
NA |
NA |
NA |
NA |
1490 |
2200 |
2200 |
| PNL4400 |
NA |
NA |
NA |
NA |
NA |
2625 |
4400 |
| PNL6600 |
NA |
NA |
NA |
NA |
NA |
NA |
6600 |
It is recommend when lifting sheets over 8', to use 2 or more lifts on a spreader bar to prevent sheet flexing, sagging or peel-off. Thin material is susceptible to magnetic bleed through, resulting in two sheets being lifted at once. **These maximum sheet lengths are selected due to the sag characteristics of the specified sheet. The item to be lifted must cover the entire length and width of the magnetic poles to properly engage and release the part. NA=Not Applicable(magnets listed will not turn "on" for specified material thickness.)
DESIGNED FOR THICK, NON-FLEXING MATERIAL
These compact, yet powerful, Rare Earth lift magnets can be used on flat or round surfaces and contain an internal release on/off device that does not contact or damage the surface of the part being lifted. Permanent magnetic lifts also eliminate the fear of dropping the load being lifted due to power failures.
- ON/OFF Rare Earth design
- Lifts flat or round loads
- Easy internal manual release does not contact the load
- Heat resistant up to 200°F (94°C)
- CONFORMS TO ASME B30.20 STANDARDS
Lock On & Off Features
The new handle on the PowerLift® Rare Earth lift magnet features a positive lock-on and lock-off mechanism that requires the operator to manually switch between the two states. This prevents the handle from being turned only ”partially on” and giving the operator a false sense of security that the magnet is holding safely, or from being accidentally bumped to the “off” position, dropping the load pre-maturely.
| Flat Lift Capacity* (LBS.) |
Round Lift Capacity* (LBS.) |
Overall Length (IN.) |
Overall Width (IN.) |
Overall Height (IN.) |
Handle (IN.) |
Weight (LBS.) |
Catalog Number |
| 220 |
110 |
5 |
2-5/8 |
6-5/8 |
5-7/8 |
7 |
PNL220 |
| 660 |
330 |
7-7/8 |
3-5/8 |
8-7/8 |
6-7/8 |
22 |
PNL660 |
| 1,300 |
660 |
10-3/4 |
4-7/8 |
8-7/8 |
6-3/4 |
53 |
PNL1300 |
| 2,200 |
1,100 |
12-5/8 |
7-1/8 |
8-7/8 |
10-1/8 |
110 |
PNL2200 |
| 4,400 |
2,200 |
16-1/2 |
9-1/4 |
18 |
16-3/4 |
325 |
PNL4400 |
| 6,600 |
3,300 |
20 |
11-1/4 |
22-1/4 |
20-5/8 |
485 |
PNL6600 |
| *Lift CapacityValues Are Stated At 33% Of The Actual Value. See Holding Value & Maximum Sheet Length Chart Below. |
| HOLDING VALUE (LBS.) & **MAXIMUM SHEET LENGTH (Due to Sag for Material Thickness for Single Magnet Use) |
| Catalog Number |
1/4" (6' Long) |
3/8" (8' Long) |
1/2" (8' Long) |
3/4" (8' Long) |
1" (10' Long) |
2" (10' Long) |
3" (10' Long) |
| PNL220 |
180 |
220 |
220 |
220 |
220 |
220 |
220 |
| PNL660 |
270 |
500 |
615 |
660 |
660 |
660 |
660 |
| PNL1300 |
NA |
NA |
800 |
1300 |
1300 |
1300 |
1300 |
| PNL2200 |
NA |
NA |
NA |
NA |
1490 |
2200 |
2200 |
| PNL4400 |
NA |
NA |
NA |
NA |
NA |
2625 |
4400 |
| PNL6600 |
NA |
NA |
NA |
NA |
NA |
NA |
6600 |
It is recommend when lifting sheets over 8', to use 2 or more lifts on a spreader bar to prevent sheet flexing, sagging or peel-off. Thin material is susceptible to magnetic bleed through, resulting in two sheets being lifted at once. **These maximum sheet lengths are selected due to the sag characteristics of the specified sheet. The item to be lifted must cover the entire length and width of the magnetic poles to properly engage and release the part. NA=Not Applicable(magnets listed will not turn "on" for specified material thickness.) |
